Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Blog Article
Just about everyone has their private opinions with regards to Installing A Bathtub.
Setting up a bath tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is easily easily accessible, the task can move quickly; if you have to open up a wall surface to get rid of the old tub and position the new tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Ensure you have qualified yourself for the job and are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed project, it is better to consider employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly assist you set up a new bathtub in your washroom if you have actually already gotten a new tub and don't need to change the setup of your previous water pipelines.
Your devices and product list need to consist of the following:
Preparing for the Installation
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipes. When the supply pipes have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing both wood boards under its feet, position the bath tub in the needed setting. The wood boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level checks out degree.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Switch on the water supply and examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill up the bathtub and additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the tub ought to wait until the bathtub has actually been made use of a minimum of once as this will resolve it right into its final position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap and the sink. Safeguard the tap in place with the maker offered backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bath as well as the tiling, bring about problems with moisture as well as possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently readily available on the market. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about A Step-by-Step Guide to Installing a Bathtub? Try to leave a review down below. We will be glad to listen to your ideas about this blog posting. We hope that you visit us again later on. For those who enjoyed reading our article plz remember to share it. Thank you for your time. Don't forget to come visit our site back soon.
Contact
Report this page